Netgear R7000 WAN connection 10Mbps











up vote
0
down vote

favorite












Just got 100Mbps internet service and pulled a Netgear R7000 out of retirement to connect to it. The router started with AdvancedTomato firmware. I noticed my speeds were peaking at 10Mbps. Looking at the router status page, I could see that the port was negotiating at 10Mbps.



A few things I've tried:





  • Different patch cables. No change.


  • Different router connected to the same Cat5e connector and cable. The other router speed test comes in at about 103Mbps.


  • Computer connected directly to the jack. Same result as connecting a different router.


  • Different firmwares. I've tried the AdvancedTomato that was on the router originally, the latest official firmware, and the latest DD-WRT firmware, all with the same result.


  • Connecting the router to other devices. When I had the AdvancedTomato firmware and could easily see the speed the port had negotiated, I connected the router's WAN port to my desktop computer's Gigabit ethernet controller using the same patch cable, and the status page reported 1000Mbps connectivity on the router's WAN port.


I had this router connected to Comcast service previously and was able to achieve >10Mbps speeds. It's only now connected to my WaveG service that it can't seem to negotiate more than 10Mbps with this one device.



I'm not sure where to go with this issue. It seems as though there's nothing wrong with my router since it gets gigabit connectivity when connected to my computer. It seems there's nothing wrong with the jack or anything behind it since other devices can get >100Mbps speeds connected to it. The cable seems to be fine since it works with other devices. I've tried every alternative firmware I'm aware of in addition to the official firmware.



I don't really want to buy a new router since that doesn't seem to be the problem. Where can I go from here?










share|improve this question


















  • 2




    Guess I am not sure why you think the router is not the problem, it clearly seems to be... perhaps problem isn't the right word here though, but incompatibility. Working for an ISP we have seen this before, it is rare but sometimes there is a just an issue where gigabit doesn't want to negotiate properly between two devices, occasionally falling to 100Mbps, and often to 10Mbps/Half-Duplex. The solution is replace one end or the other (router or modem) or put something in between, like a small 5-port gigabit switch.
    – acejavelin
    Nov 17 at 19:40










  • @acejavelin I agree with you. An unmanaged switch would work for that, right? I think I'll order one and give it a shot.
    – raddevon
    Nov 17 at 19:59






  • 1




    Yes, should be fine.
    – acejavelin
    Nov 17 at 20:04















up vote
0
down vote

favorite












Just got 100Mbps internet service and pulled a Netgear R7000 out of retirement to connect to it. The router started with AdvancedTomato firmware. I noticed my speeds were peaking at 10Mbps. Looking at the router status page, I could see that the port was negotiating at 10Mbps.



A few things I've tried:





  • Different patch cables. No change.


  • Different router connected to the same Cat5e connector and cable. The other router speed test comes in at about 103Mbps.


  • Computer connected directly to the jack. Same result as connecting a different router.


  • Different firmwares. I've tried the AdvancedTomato that was on the router originally, the latest official firmware, and the latest DD-WRT firmware, all with the same result.


  • Connecting the router to other devices. When I had the AdvancedTomato firmware and could easily see the speed the port had negotiated, I connected the router's WAN port to my desktop computer's Gigabit ethernet controller using the same patch cable, and the status page reported 1000Mbps connectivity on the router's WAN port.


I had this router connected to Comcast service previously and was able to achieve >10Mbps speeds. It's only now connected to my WaveG service that it can't seem to negotiate more than 10Mbps with this one device.



I'm not sure where to go with this issue. It seems as though there's nothing wrong with my router since it gets gigabit connectivity when connected to my computer. It seems there's nothing wrong with the jack or anything behind it since other devices can get >100Mbps speeds connected to it. The cable seems to be fine since it works with other devices. I've tried every alternative firmware I'm aware of in addition to the official firmware.



I don't really want to buy a new router since that doesn't seem to be the problem. Where can I go from here?










share|improve this question


















  • 2




    Guess I am not sure why you think the router is not the problem, it clearly seems to be... perhaps problem isn't the right word here though, but incompatibility. Working for an ISP we have seen this before, it is rare but sometimes there is a just an issue where gigabit doesn't want to negotiate properly between two devices, occasionally falling to 100Mbps, and often to 10Mbps/Half-Duplex. The solution is replace one end or the other (router or modem) or put something in between, like a small 5-port gigabit switch.
    – acejavelin
    Nov 17 at 19:40










  • @acejavelin I agree with you. An unmanaged switch would work for that, right? I think I'll order one and give it a shot.
    – raddevon
    Nov 17 at 19:59






  • 1




    Yes, should be fine.
    – acejavelin
    Nov 17 at 20:04













up vote
0
down vote

favorite









up vote
0
down vote

favorite











Just got 100Mbps internet service and pulled a Netgear R7000 out of retirement to connect to it. The router started with AdvancedTomato firmware. I noticed my speeds were peaking at 10Mbps. Looking at the router status page, I could see that the port was negotiating at 10Mbps.



A few things I've tried:





  • Different patch cables. No change.


  • Different router connected to the same Cat5e connector and cable. The other router speed test comes in at about 103Mbps.


  • Computer connected directly to the jack. Same result as connecting a different router.


  • Different firmwares. I've tried the AdvancedTomato that was on the router originally, the latest official firmware, and the latest DD-WRT firmware, all with the same result.


  • Connecting the router to other devices. When I had the AdvancedTomato firmware and could easily see the speed the port had negotiated, I connected the router's WAN port to my desktop computer's Gigabit ethernet controller using the same patch cable, and the status page reported 1000Mbps connectivity on the router's WAN port.


I had this router connected to Comcast service previously and was able to achieve >10Mbps speeds. It's only now connected to my WaveG service that it can't seem to negotiate more than 10Mbps with this one device.



I'm not sure where to go with this issue. It seems as though there's nothing wrong with my router since it gets gigabit connectivity when connected to my computer. It seems there's nothing wrong with the jack or anything behind it since other devices can get >100Mbps speeds connected to it. The cable seems to be fine since it works with other devices. I've tried every alternative firmware I'm aware of in addition to the official firmware.



I don't really want to buy a new router since that doesn't seem to be the problem. Where can I go from here?










share|improve this question













Just got 100Mbps internet service and pulled a Netgear R7000 out of retirement to connect to it. The router started with AdvancedTomato firmware. I noticed my speeds were peaking at 10Mbps. Looking at the router status page, I could see that the port was negotiating at 10Mbps.



A few things I've tried:





  • Different patch cables. No change.


  • Different router connected to the same Cat5e connector and cable. The other router speed test comes in at about 103Mbps.


  • Computer connected directly to the jack. Same result as connecting a different router.


  • Different firmwares. I've tried the AdvancedTomato that was on the router originally, the latest official firmware, and the latest DD-WRT firmware, all with the same result.


  • Connecting the router to other devices. When I had the AdvancedTomato firmware and could easily see the speed the port had negotiated, I connected the router's WAN port to my desktop computer's Gigabit ethernet controller using the same patch cable, and the status page reported 1000Mbps connectivity on the router's WAN port.


I had this router connected to Comcast service previously and was able to achieve >10Mbps speeds. It's only now connected to my WaveG service that it can't seem to negotiate more than 10Mbps with this one device.



I'm not sure where to go with this issue. It seems as though there's nothing wrong with my router since it gets gigabit connectivity when connected to my computer. It seems there's nothing wrong with the jack or anything behind it since other devices can get >100Mbps speeds connected to it. The cable seems to be fine since it works with other devices. I've tried every alternative firmware I'm aware of in addition to the official firmware.



I don't really want to buy a new router since that doesn't seem to be the problem. Where can I go from here?







networking router wireless-router dd-wrt






share|improve this question













share|improve this question











share|improve this question




share|improve this question










asked Nov 17 at 19:29









raddevon

126117




126117








  • 2




    Guess I am not sure why you think the router is not the problem, it clearly seems to be... perhaps problem isn't the right word here though, but incompatibility. Working for an ISP we have seen this before, it is rare but sometimes there is a just an issue where gigabit doesn't want to negotiate properly between two devices, occasionally falling to 100Mbps, and often to 10Mbps/Half-Duplex. The solution is replace one end or the other (router or modem) or put something in between, like a small 5-port gigabit switch.
    – acejavelin
    Nov 17 at 19:40










  • @acejavelin I agree with you. An unmanaged switch would work for that, right? I think I'll order one and give it a shot.
    – raddevon
    Nov 17 at 19:59






  • 1




    Yes, should be fine.
    – acejavelin
    Nov 17 at 20:04














  • 2




    Guess I am not sure why you think the router is not the problem, it clearly seems to be... perhaps problem isn't the right word here though, but incompatibility. Working for an ISP we have seen this before, it is rare but sometimes there is a just an issue where gigabit doesn't want to negotiate properly between two devices, occasionally falling to 100Mbps, and often to 10Mbps/Half-Duplex. The solution is replace one end or the other (router or modem) or put something in between, like a small 5-port gigabit switch.
    – acejavelin
    Nov 17 at 19:40










  • @acejavelin I agree with you. An unmanaged switch would work for that, right? I think I'll order one and give it a shot.
    – raddevon
    Nov 17 at 19:59






  • 1




    Yes, should be fine.
    – acejavelin
    Nov 17 at 20:04








2




2




Guess I am not sure why you think the router is not the problem, it clearly seems to be... perhaps problem isn't the right word here though, but incompatibility. Working for an ISP we have seen this before, it is rare but sometimes there is a just an issue where gigabit doesn't want to negotiate properly between two devices, occasionally falling to 100Mbps, and often to 10Mbps/Half-Duplex. The solution is replace one end or the other (router or modem) or put something in between, like a small 5-port gigabit switch.
– acejavelin
Nov 17 at 19:40




Guess I am not sure why you think the router is not the problem, it clearly seems to be... perhaps problem isn't the right word here though, but incompatibility. Working for an ISP we have seen this before, it is rare but sometimes there is a just an issue where gigabit doesn't want to negotiate properly between two devices, occasionally falling to 100Mbps, and often to 10Mbps/Half-Duplex. The solution is replace one end or the other (router or modem) or put something in between, like a small 5-port gigabit switch.
– acejavelin
Nov 17 at 19:40












@acejavelin I agree with you. An unmanaged switch would work for that, right? I think I'll order one and give it a shot.
– raddevon
Nov 17 at 19:59




@acejavelin I agree with you. An unmanaged switch would work for that, right? I think I'll order one and give it a shot.
– raddevon
Nov 17 at 19:59




1




1




Yes, should be fine.
– acejavelin
Nov 17 at 20:04




Yes, should be fine.
– acejavelin
Nov 17 at 20:04















active

oldest

votes











Your Answer








StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "3"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);

StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});

function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
convertImagesToLinks: true,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: 10,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});


}
});














 

draft saved


draft discarded


















StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f1376295%2fnetgear-r7000-wan-connection-10mbps%23new-answer', 'question_page');
}
);

Post as a guest















Required, but never shown






























active

oldest

votes













active

oldest

votes









active

oldest

votes






active

oldest

votes
















 

draft saved


draft discarded



















































 


draft saved


draft discarded














StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f1376295%2fnetgear-r7000-wan-connection-10mbps%23new-answer', 'question_page');
}
);

Post as a guest















Required, but never shown





















































Required, but never shown














Required, but never shown












Required, but never shown







Required, but never shown

































Required, but never shown














Required, but never shown












Required, but never shown







Required, but never shown







Popular posts from this blog

AnyDesk - Fatal Program Failure

How to calibrate 16:9 built-in touch-screen to a 4:3 resolution?

QoS: MAC-Priority for clients behind a repeater